We've detected you are coming from a location where we have a regional site.
Please choose one of the following sites:

Firmware archive.

 

Sensor Unit firmware H4D-60 R500

Version R500 is a replacement firmware for R361 introducing many new features and performance improvements for the H4D-60 camera.

Highlights IncludeIMPORTANT NOTICE: During the upgrade procedure do NOT disconnect the firewire cable until prompted!

Note: These new features require H4D Camera Body firmware version 2.2.4 and Camera Viewfinder HVD90X & HV90x-II firmware version 2.2.0. These firmware versions can be found further down on this page.

This firmware update is intended for Phocus users only and can be downloaded via Phocus version 2.5.5 Mac, 2.5.5 Windows or newer versions. For a complete list of fixes and added features, please consult the read-me file.
     
 
 
 

Sensor Unit firmware H4D-40/50/200MS, R365

Version R365 is a replacement firmware for R361 introducing many new features and performance improvements for the H4D-40, H4D-50, H4D-50MS, H3DII-50, H3DII-50MS, H4D-200MS & CFV50 cameras.


Highlights Include (H4D-40/50/50MS/200MS only)

  • Rear LCD updated to full resolution*
  • One click 100% instant focus check
  • Camera grip info on rear LCD
  • Two directional electronic spirit level
*) Does not apply to H4D-50 units upgraded from H3DII-50

General changes

  • Enable exposure of 128 seconds via Phocus for CFV-50
  • improved firmware update procedure via Phocus
  • User interface and stability optimization


Please consult the updated H4D manual on functionality of all new features.

IMPORTANT NOTICE: During the upgrade procedure do NOT disconnect the firewire cable until prompted!

Note: These new features require H4D Camera Body firmware version 2.2.4 and Camera Viewfinder HVD90X & HV90x-II firmware version 2.2.0. These firmware versions can be found further down on this page.

This firmware update is intended for Phocus users only and can be downloaded via Phocus version 2.5.5 Mac, 2.5.5 Windows or newer versions. For a complete list of fixes and added features, please consult the read-me file.
     
 
 
 

Sensor Unit firmware H4D-60, R361

Version R361 is a performance and stability release of version R354 and contains various improvements and fixes for the H4D-60 camera.


Highlights Include

  • Flash sync support for use with manual shutters and technical cameras
  • Support for Sandisk Extreme Pro 128GB CF card
  • Improved initial hardware preview on back display as well as in Phocus
  • Improved capture speed performance both tethered and untethered
  • Stability improvements


This firmware update is intended for Phocus users only and can be downloaded via Phocus version 2.5.5 Mac, 2.5.5 Windows or newer versions. For a complete list of fixes and added features, please consult the read-me file.

     
 
 
 

Sensor Unit firmware H4D-40/50/200MS, R361

Firmware version R361 for H4D-40, H4D-50, H4D-50MS, H3DII-50, H3DII-50MS, H4D-200MS & CFV50

This package contains firmware version R361.CIM for the above listed products.
Version R361 is a feature and bug fix release of version R359 and contains various improvements and fixes.

Changes since version R359:


  • Support for Sandisk 128GB CF cards
  • 128 second exposure time enabled on 50mp sensor products (CFV-50 currently not included)
  • H4D-200MS camera support
  • "Empty batch" unintentionally displayed has been fixed
  • A problem with double exposure on some mechanical shutters in flash sync mode fixed
  • Power down not working bug fixed. New minimum setting at 5 min and default setting at 30 min.
  • Live Video stability improved

    NB: Please note that when attaching an imagebank II, which has been formatted in a previous firmware, you will be prompted to format the imagebank.
    This is due to a new cluster size and formatting routine. If you are not ready to delete all images on the Imagebank II do NOT perform the formatting procedure or upgrade to R361.




    This firmware update is intended for Phocus users only and can be downloaded via Phocus version 1.1 Mac, 1.0.2 Windows or newer versions. For a complete list of fixes and added features, please consult the read-me file.
  •      
     
     
     

    Camera Body firmware: H4D, H3DII, H3D, H2D 2.2.4/16.0.6

    Firmware version 2.2.4/16.0.6 is a bug fix release related to users of True Focus only.

    Firmware package CB120131.hbf requires one of the above mentioned Hasselblad digital capture products and is only necessary if True Focus is used.
    Other cameras than H4D will not benefit from this upgrade.

    Fixes

    • A bug which could cause incorrect angle measurements in True Focus to be applied after a lens change has been fixed



    The firmware package CB120131.hbf for the H-series camera body, contains the following firmware versions:


    ProductFirmware Version
    H4D2.2.4/16.0.6
    H3DII, H3D, H2D2.2.4


    This firmware update is only possible via Phocus version 1.1.3 Mac, 1.0.2 Windows (or later). Please be aware that H4D camera models require Phocus 2.0 (or later) in order to function properly.

    For a complete description of fixes, added features, installation procedures and limitations, please consult the read-me file.
         
     
     
     

    Camera Body firmware: H4X 2.2.5/16.0.6

    Firmware version 2.2.5/16.0.6 is a bug fix release related to users of True Focus only.

    Firmware package H4X120131.hbf is for the Hasselblad H4X camera body only and is necessary if True Focus is used.

    Fixes

    • A bug which could cause incorrect angle measurements in True Focus to be applied after a lens change has been fixed



    The firmware package H4X120131.hbf for the H4X camera body, contains the following firmware versions:


    ProductFirmware Version
    H4X2.2.5/16.0.6


    This firmware update is only possible via Phocus version 1.1.3 Mac, 1.0.2 Windows (or later).
    To perform this camera body upgrade you must attach a Hasselblad digital back to the H4X body. (compatible digital backs include CF, CFH, H2D, H3D, H3DII & H4D)

    For a complete description of fixes, added features, installation procedures and limitations, please consult the read-me file.
         
     
     
     

    Sensor Unit Firmware H5D-40 & H5D-50, 1.5.3R

    Version 1.5.3R is a replacement firmware for 1.2.0R, and is recommended for all H5D users.

    Highlights Include

    • Nine view feature added
    • Mark overexposure feature added
    • Chinese language support
    • Numerous bug fixes and stability improvements

    After installing 1.5.3R you should proceed to install Camera Body Firmware H5D130506.hbf

    This firmware update is intended for Phocus users only and can be downloaded via Phocus version 2.7 Mac, 2.7 Windows or newer versions. For a complete list of fixes and added features, please consult the read-me file.

         
     
     
     

    Camera Body firmware: H5D, 3.1.3/1.1.2

    Firmware version 3.1.3/1.1.2 is a feature release

    Firmware package H5D130506.hbf is ONLY for Hasselblad H5D cameras


    Highlights

    • Shortest Interval time is set to 2 seconds
    • Fixed a bug that sometimes caused an extra short delay in the exposure sequence
    • Bug fixes and stability improvements


    The firmware package H5D130506.hbf for the H5D-series camera body, contains the following firmware versions:


    ProductFirmware Version
    H5D3.1.3/1.1.2


    This firmware update is intended for Phocus users only and can be downloaded via Phocus version 2.7 Mac, 2.7 Windows or newer versions. For a complete list of fixes and added features, please consult the read-me file.

    IMPORTANT NOTICE: Before performing this upgrade you must first install the Sensor Unit firmware 1.5.3R!

    For a complete description of fixes, added features, installation procedures and limitations, please consult the read-me file.
         
     
     
     

    Camera Body firmware: H1D, H1, H2, H2F

    Firmware package 081222.hbf requires one of the above Hasselblad camera/camera body and is a comprehensive firmware package containing various firmware versions with improvements and fixes for your camera body.

    Highlights Include
    • HTS1.5
    • HCD 35-90 zoom lens *
    • DC Power Grip

      * Relevant for H2F only with Hasselblad CF and CFH digital backs.

    The 081222.hbf firmware package contains the following firmware versions:

    ProductFirmware Version
    H1D, H1, H29.5.0
    H2F1.1.0

    This firmware update is only possible via Phocus version 1.1.3 Mac, 1.0.2 Windows or later.

    For a complete description of fixes, added features, installation procedures and limitations, please consult the read-me file.
         
     
     
     

    Sensor Unit Firmware 3.5.8R

    This version is a feature update for the CMOS based H5D-50c and CFV-50c cameras. CCD based cameras cannot use this update.

    Highlights Include:

    • Live View on the rear display
    • Longer exposure time. Now up to 34 minutes (no black exposure required)
    • Faster capture rate. Now 50 frames per minute (H5D-50c only)
    • ISO and White Balance setting visible in viewfinder (H5D-50c only)
    • Spirit Level (H5D-50c only) and selectable display modes in tethered mode
    • Korean language added

    This firmware update is intended for Phocus users only and can be downloaded via Phocus version 2.8.1 or later. For a complete list of fixes and added features, please consult the read-me file.
         
     
     
     

    Sensor Unit Firmware 3.4.3R

    This version is a feature update and is only for all H5D-50c users. CCD based H5D cameras cannot use this update.

    Highlights Include

    • Support for operation on technical cameras, including Flash Sync, Pinhole, Rollei and Schneider electronic shutters
    • Colour Live video in Phocus
    • ¼ resolution JPEG

    This firmware update is intended for Phocus users only and can be downloaded via Phocus version 2.8.1 or later. For a complete list of fixes and added features, please consult the read-me file.
         
     
     
     

    Sensor Unit Firmware 2.4.3R

    Version 2.4.3R is recommended for all H5D users.

    Highlights Include

    • Faster start-up time
    • Technical camera mode (Flash sync and pinhole)
    • Support for GPS module (GIL)
    • Folder view
    • Improved histogram
    • Improved 9-view
    • Language support: English, Spanish, French, German, Italian, Japanese, Chinese

    After installing 2.4.3R you should proceed to install Camera Body Firmware H5D131008.hbf

    This firmware update is intended for Phocus users only and can be downloaded via Phocus version 2.7 Mac, 2.7 Windows or newer versions. For a complete list of fixes and added features, please consult the read-me file.
         
     
     
     

    Camera Body firmware: H5D 3.3.1/1.1.4

    Firmware version 3.3.1 is a maintenance release for all H5D-50c camera bodies but should be installed in all H5D camera bodies. It is a release to support the extended functionality (Live Video, Technical cameras, JPEG) that is added to the 50c with the new 3.4.3 firmware.

    The firmware package H5D140630.hbf for the H-series camera body, contains the following firmware versions:

    Product Firmware Version

    H5D 3.3.1/1.1.4

    Please use the latest version of Phocus to download the new firmware.
         
     
     
     

    Sensor Unit firmware H4D-60, R512

    Version R512 is a replacement firmware for R500, primarily introducing support on the H4D-60 camera for new lenses.

    Highlights Include

    • Support for the new HCD 24mm
    • Support for the new Macro Converter

    IMPORTANT NOTICE: During the upgrade procedure do NOT disconnect the firewire cable until prompted!

    Note: These new features require H4D Camera Body firmware version 2.2.4 and Camera Viewfinder HVD90X & HV90x-II firmware version 2.2.0. These firmware versions can be found further down on this page.

    This firmware update is intended for Phocus users only and can be downloaded via Phocus version 2.5.5 Mac, 2.5.5 Windows or newer versions. For a complete list of fixes and added features, please consult the read-me file.

         
     
     
     

    Sensor Unit firmware H4D-40/50/200MS, R366

    Version R366 is a replacement firmware for R365, primarily introducing support on the H4D-40, H4D-50, H4D-50MS, H3DII-50, H3DII-50MS, H4D-200MS & CFV50 cameras for new lenses.

    Highlights Include:

    • Support for the new HCD 24mm
    • Support for the new Macro Converter

    IMPORTANT NOTICE: During the upgrade procedure do NOT disconnect the firewire cable until prompted!

    Note: These new features require H4D Camera Body firmware version 2.2.4 and Camera Viewfinder HVD90X & HV90x-II firmware version 2.2.0. These firmware versions can be found further down on this page.

    This firmware update is intended for Phocus users only and can be downloaded via Phocus version 2.5.5 Mac, 2.5.5 Windows or newer versions. For a complete list of fixes and added features, please consult the read-me file.